B&G Parts & Repair Equipment

B&G Equipment, such as Primeline Sprayers and Termite Tools, is built to last, but even the best equipment will inevitably take some wear over time. Solutions Pest & Lawn is your one-stop shop for everything you need to make sure you get the most out of every product you buy from us. 

Most B&G parts are explicitly made for B&G equipment, so it is unlikely that you will find replacement parts at hardware stores. We carry a complete inventory of replacement parts for our B&G offerings. Usually, a simple replacement part will have your broken-down sprayer working like new again, saving you hundreds, if not thousands, of dollars.

Our Recommendation

We recommend two kits that are must-haves for any applicator who uses B&G pump sprayers regularly: the B&G Gasket Repair Kit and the B&G Strainer Kit. These two kits contain essential parts that will fix various common B&G sprayer issues, from clogs to leaks.

User Guide

Together, the B&G Gasket Repair Kit and the B&G Strainer Kit will fix most typical operation issues that both PCOs and serious DIYers who use B&G sprayers might encounter. Some of the most common issues B&G sprayer users encounter are clogged lines and screens, leaks, and minor pressure issues. The parts included in these two kits can easily rebuild one B&G pump sprayer. 

Step 1: Disassembly

You will first need to disassemble your B&G Sprayer to install the new replacement parts. This can be quick or take some time, depending on the part that needs replacing and its location. When utilizing a kit that replaces multiple worn parts, it's best to do a complete disassembly by following the manual instructions for details on how to disassemble and in what order.

Step 2: Replace Parts

Once your sprayer has been taken apart, installing the new parts is simple. Remove the old parts and pieces, replace them with the new parts, and make sure to tighten them securely in place.

Step 3: Reassembly and Testing

After the parts have been replaced, reassemble the sprayer. You should test the sprayer with clean water to see if the equipment parts work as intended. In some cases, parts may have been put on incorrectly or not tightly enough. If so, you would have to disassemble the sprayer again to pinpoint the part that needs adjustment. If you perform a test spraying and all is well, you have completed part replacement.

Inspection and Maintenance

It is always a good idea to check and maintain your equipment. Typically, we recommend that B&G sprayer users inspect their sprayer and its parts quarterly or annually, depending on use. Inspecting the parts and replacing any worn gaskets, screens, or seals before you reach operation failure is always best. These parts are considered wear and tear parts, meaning that they commonly degrade over time through everyday operational use. 

Regular Cleaning

A familiar issue users face is clogged lines. This usually happens due to a dirty or blocked strainer screen. The strainer screen is located within the valve extension, where the extended-ban handle connects to the sprayer hose. This screen will collect dirt and other debris that might accidentally be mixed with your solution before it travels through the wand to be sprayed.

To clean the strainer screen, remove it from the valve extension by disconnecting the extended-ban wand from the hose. Clean the screen with a wire brush or water, careful not to damage the screen. If the screen is beyond repair, it can be replaced with the screen found in the B&G Strainer Kit.

Inspect Gaskets, Washers, etc.

You will need to take some time to check the remaining parts of the sprayer for signs of damage, erosion, or fragility. These parts range in material from polypropylene, viton rubber, and nylon. As hardy and reliable as these parts are, they will weaken over time, mainly when acidic and oil-based products are used in the sprayer.

When you check the parts, look for cracks and erosion. The B&G Gasket Repair Kit contains each main component for quick and easy replacement.

Parts

The B&G Gasket Repair Kit and the B&G Strainer Kit contain everything you need to replace worn or damaged parts and rebuild your B&G pump sprayer.

Strainer Kit

The Strainer Kit consists of the strainer screen and the body piece that holds the screen.

Gasket Repair Kit

The Gasket Repair Kit contains a variety of parts. These are:

• Check valve
• Tank gasket
• Spreader Plate
• Polypropylene plunger cup + lubricant
• Lock spring
• Hose coupling washer
• Viton tip gasket
• Nylon gasket
• Valve packing (3)
• Valve spring
• Soft seat gasket

Key Takeaways

• It is important to always perform routine maintenance and inspections of equipment before it goes bad. We usually recommend doing this every three months or at least once a year, depending on use.
• Always consider the chemicals you are using with your sprayer and other equipment. Caustic and oil-based products will likely deteriorate most gaskets and seals quicker than water-based or less corrosive materials. If you use ECs or products like herbicides often, you will want to inspect and replace your parts regularly for top performance.