• Call (800) 479-6583
  • Mon-Fri 8am-5pm
  • |
  • Sat 9am-5pm
Menu

Mistaway (M) Gen 1.3/3 - Motor 1/2 HP

Free Shipping on All Orders

Target Pests

Mosquitoes

For Use In

Mistaway Mosquito Misting system

Application

The motor is located in the lower left corner of the unit. The sidewalls must be removed to access it.

How To

1. Remove sidewalls, controller and shroud. See Gen 3: Access Components by Removing Sidewalls.

A. The pump and motor will be exposed in the back left corner of the unit.


2. Remove existing motor and disconnect the motor cable.

A. IMPORTANT!! Unplug the motor cable connector from the controller port marked "Motor."

B. Using Phillips screwdriver, remove the screw in the clamp that connects the pump and motor and pull the pump off the motor.

C. Use the 1/2" ratcheting wrench to remove the nuts that secure the motor to the floor of the unit. Save the nuts and lock washers and remove the motor from the unit.

D. On the end of the motor where the cable is connected, use the nut driver to remove the two black screws from the gray cover plate and remove the plate.


E. Loosen the green screw and disconnect the green lead. Disconnect the white and black leads from their connections. Discard the motor but keep the cable.


3. Connect motor cable to new motor and test.

A. See photo. Remove the gray cover plate from the new motor. Connect the black lead to the terminal marked "1" and the white lead to the terminal marked "4".


B. Use the 1/4" nut driver to loosen the green screw. Slide the connector on the green lead onto the post and tighten the screw.


C. Connect the motor cable connector to the controller port marked "Motor."

D. Holding the motor, run a Manual Mist to confirm that the motor spins when powered.

 

4. Secure motor to unit floor, connect pump to motor and test.

A. IMPORTANT!! Unplug the motor cable connector from the controller port marked "Motor."

B. Orient the motor so that the cable end is nearest the front of the unit. Place the motor over the 4 studs in the base of the unit and add lock washers. Use the 1/2" ratcheting wrench to secure the motor.

C. Slide clamp with screws over pump and mate pump shaft to motor. Use phillips screwdriver to tighten clamp.

D. Ensure the pump intake and discharge tubing are secure in the push-to-connect fittings.

E. Run a Manual Mist to confirm the unit is working.


5. Replace shroud, controller and sidewalls. See Gen 3: Access Components by Removing Sidewalls.

Mistaway (M) Gen 1.3/3 - Motor 1/2 HP

$139.47
$139.47

Works with all units.

MistAway Motor 0.5 HP

Part Number 

10800

 

Works with all units.

MistAway Motor 0.5 HP

Part Number 

10800

 

Product Q & A

Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Will this Motor fit on any mosquito misting system? I do not have a Mistaway system, but my motor and pump went out.
Motorhead on May 24, 2017
BEST ANSWER: This Motor is meant to be placed on the Mistaway units. If both the motor and the pump are out I would suggest looking into an upgrade kit. This will convert your unit into a Mistaway unit.

https://www.solutionsstores.com/gen-1-2-upgrade-kit-to-gen-1-3-w-agitator-system

Customer Reviews

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
All I needed
Easy to put on the motor and it arrived quick, was able to get my Mistaway misting system up and running.
May 24, 2017

Contact Us

x

Need Help?

Call us at (800)479-6583

Se habla español

Mon-Fri 8am-5pmSat 9am-5pm

Receive a reply in less than 1 hour
(during business hours)

Follow us

* Required Fields