• Call (800) 479-6583
  • Mon-Fri 8am-5pm
  • |
  • Sat 9am-5pm
Menu

Gopher Getter Type 2

Free Shipping on All Orders

Target Pests

Pocket gophers

Application

1. GOPHER BAIT APPLICATOR METHOD: Turn hand probe unit upside down to attach or remove bait bottle which screws into the dispenser. The 1-lb. container for Gopher Getter Type 2 Bait by Wilco may be screwed directly into the dispenser. Otherwise, add the amount of bait needed to the bottle that comes with the Gopher Bait Applicator and screw the bottle into the dispenser. Using probe end, probe around mounds to locate runways (see “Locating runways” above.) Lift handle three times to deposit bait in each active runway. Pick up or bury any spilled bait immediately. Makes 2-7 bait sets per burrow system, depending upon the systems apparent length. For best results, this bait must be placed in the gophers’ active runway for four (4) consecutive days or until activity ceases.

2. HAND PROBE AND FUNNEL METHODS: Enlarge probe hole(if necessary) to accommodate baiting. Use water proof gloves and a scooping device (preferably long-handled) to transfer the bait from container to the bait applicator. Insert one-half cup bait into each active runway through probe opening or through the funnel, if using the Probe’ n Funnel kit. Take care not to spill bait on the surface. Pick up any spilled bait immediately. Makes 2-7 bait sets per burrow system, depending upon the systems apparent length. For best results, this bait must be placed in the gophers’ active runway for four (4) consecutive days or until activity ceases.

3. GOPHER GETTER MIDGET: Remove cap from built-in bait reservoir and fill with bait. Replace and tighten cap. Using probe, probe around mounds to locate runways. To deposit bait in each active runway, turn crank six full turns, stopping back at the closed position. For best results, this bait must be placed in the gophers’ active runway for four (4) days in a row or until activity ceases.

CLOSING RUNWAYS - After bait has been applied, cover probe opening with sod or dirt. Do not permit dirt to sift in or cover bait.

POST-APPLICATION DIRECTIONS: Using waterproof gloves, collect and burn (where permitted) or bury all visible dead animals. Dispose of leftover bait according to pesticide disposal on product label.

Active Ingredient

Diphacionone — .005% (anti-coagulant)

Be the first to review this product

Product Q & A

Answers ()

Gopher Getter Type 2

$19.99
$69.99
$19.99
An anise coating is applied to milo grain, becoming an attractant and providing a high acceptance rate among Pocket Gophers (as proven in lab studies). It is dispensed easily through our applicators and most other application equipment. The gopher(s) must eat the bait 3 to 4 days in a row. You can achieve this by applying 1/2 cup of bait per burrow set.
An anise coating is applied to milo grain, becoming an attractant and providing a high acceptance rate among Pocket Gophers (as proven in lab studies). It is dispensed easily through our applicators and most other application equipment. The gopher(s) must eat the bait 3 to 4 days in a row. You can achieve this by applying 1/2 cup of bait per burrow set.
Product Q & A
Sort by
Most Recent Questions
GO | Reset
Expand all
Be the first to ask a question about this product
* Nickname:

* Your Answer:


Sign Up for Newsletter

Answer this Question
Hide the Form
Ask a New Question
* Nickname:

* Your Question:


Notify me by email when answer received

Sign Up for Newsletter

Add Question

Contact Us

x

Need Help?

Call us at (800)479-6583

Se habla español

Mon-Fri 8am-5pmSat 9am-5pm

Receive a reply in less than 1 hour
(during business hours)

Follow us

* Required Fields

Help