6.5HP 212cc OHV Horizontal Engine

This 6.5HP 212cc OHV Horizontal Engine, manufactured by Solutions Pest and Lawn, is a powerful and long-lasting gas engine with user-friendly controls. Its 0.9-gallon fuel capacity allows for easier startup and operation for up to 3 hours.

This efficient engine features a resistant cast iron cylinder and a low oil sensor that shuts the engine down when oil levels reach low levels, ensuring safe operation and transport to application sites.

The 6.5HP 212cc OHV Horizontal Engine is an ideal replacement engine with optimal performance without wear and tear.

Tools Needed

To use this engine you will need to install the product to a spray rig or similar devices with a power screwdriver.

How to Use

• Step 1: Before servicing, maintenance, or cleaning, turn the engine switch to the "OFF" position. Allow the engine to cool completely. Inspect the engine and equipment for damaged, loose, and missing parts before setting up and starting. If any problems are found, do not use the equipment until it is fixed properly.
• Step 2: Check oil and fuel levels. If needed, fill the fuel and replace the oil. Fill the fuel tank in a well-ventilated area away from ignition sources. Wait until the engine is excellent before adding fuel. Clean the fuel tank cap and the area around it. Unscrew and remove the fuel cap. Remove the strainer and any dirt or debris, and then replace the filter. If fuel is low, then fill the Fuel Tank to about 1 inch under the fill neck with 87 octane or higher unleaded gasoline treated with a fuel stabilizer additive. Then, replace the fuel tank. The engine is not designed for an E85 Ethanol blend.
• Step 3: Mount the engine in place.

To Start the Engine

• Step 1: To start a cold engine, move the Choke to the START position. To restart a warm engine, leave the Choke in the RUN position.
• Step 2: Open the Fuel Valve.
• Step 3: Slide the Throttle or Speed Control Lever to 1/3 away from the SLOW position (the "turtle").
• Step 4: Turn the engine on.
• Step 5: Grip the Starter Handle of the engine loosely and pull it slowly several times to allow the gasoline to flow into the Engine's carburetor. Then, pull the Starter Handle gently until resistance is felt. Allow the Cable to retract fully and then pull it quickly. Repeat until the engine starts. Do not let the Starter Handle snap back against the engine; hold it as it recoils so it doesn't hit the engine.
• Step 6: Allow the engine to run for several seconds. Then, if the Choke lever is in the Start position, move the Choke lever very slowly so it's in the RUN position. Allow the engine to run at no load for five minutes after each start-up to stabilize the engine.
• Step 7: Adjust the throttle as needed.

To Stop the Engine

• Step 1: To stop the engine in an emergency, turn the Engine Switch off.
• Step 2: Under normal conditions, slide the Throttle or Speed Control Lever to SLOW (the turtle).
• Step 3: Turn the Engine switch off.
• Step 4: Close the fuel valve.

Where to Use

The 6.5HP 212cc OHV Horizontal Engine can be used for professional spray rig systems, lawn mowers, log splitters, pressure washers, tillers, water pumps, chippers/shredders, generators, blowers, and other types of machines.

When to Use

Use this product when the current engine on your spray rig or other machine needs to be replaced or upgraded.

Safety Information

This 6.5HP 212cc OHV Horizontal Engine is safe to use around children and pets when applied according to the product manual instructions. Always wear the appropriate personal protective equipment (PPE) when handling this product.

Keep children away from the equipment, especially while its operating. Keep all spectators at least six feet from the Engine during operations.

Do not touch the engine during use and let it cool down after use.

Special Considerations

Operation of this equipment may create sparks that can start fires around dry vegetation. A spark arrestor may be required. The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements.

There is no gear reduction.

Depending on the pump used with the motor there is hang-off on the left and/or front. Motor shaft is 3/4" and bolt size is 5/16".

Mounting pattern is 162mm L by 75.5mm W - 80.5mm W (6.40 in. L by 2.95 in. W - 3.17 in. W).

We do not accept returns on equipment or electronics; all sales are final. We do this to ensure that the products we send out are brand new, never opened, and fully operational for our customers and that their respective manufacturer's warranties cover the packages.