Solutions Polyurethane Foam Gun, manufactured by Solutions Pest and Lawn, is a lightweight and compact metal foam gun that provides consistent control over every seal, gap, and joint ensuring the most experienced professional or beginner applicator gets the maximum yield out of each polyurethane foam bottle.

This durable metal foam gun features an ergonomic two-finger trigger to ensure effortless control and comfort for long periods of time during applications. This all purpose foam application gun also supports a moderately long extrusion pipe to accurately control material flow regulation, helping to minimize foam waste.

Solutions Polyurethane Foam Gun provides greater precision for a variety of large to small scale treatments to access hard-to-reach areas in a fast and simple manner.

Tools Needed

Solutions Polyurethane Foam Gun comes ready to use with no additional application tools necessary.

This is the foam gun only. A separate purchase of a foam product will be necessary.

How to Use

• Step 1: Before applying any foam, ensure the treatment area is clean and clear. Brush away any dust and loose particles, and wipe away grease from the surfaces to be treated. Check the Solutions Polyurethane Foam Gun is ready for use before using it.
• Step 2: Shake the selected product bottle well and remove the closing cap. To install the foam canister onto the Solutions Polyurethane Foam Gun, hold the gun upside down and screw the canister into the guns adapter. Do this quickly to avoid any leakage out and fouling the adapter. Any foam that may have leaked out must be removed at once with the appropriate cleaner.
• Step 3: Once the foam canister is connected, hold the Solutions Polyurethane Foam Gun upright and shake it up and down roughly 20 times. Loosen the gun's control knob and begin to apply foam by squeezing the trigger. Adjust the amount of foam to be applied by turning the flow regulator wheel (control knob) clockwise to reduce the flow and/or to obtain a thinner layer; turn counterclockwise to increase the flow and/or to obtain a thicker layer. This regulation is required to obtain a thicker layer. Allow the foam time to expand and cure.
• Step 4: In order to substitute the foam can, turn the Solutions Polyurethane Foam Gun upside down as in picture 1 of the product manual. Push the lever in order to release any leftover material. To clean the internal foam gun barrel, you will need to attach a foam cleaner to the gun adapter and spray until the gun is completely clean. The adapter, the nozzle and the spray head must always be clean with an appropriate foam cleaner to avoid damages and potential foam-build-up.

Where to Use

The Solutions Polyurethane Foam Gun may be used to apply foam for pest exclusion on residential and commercial properties. Use it to apply foam to thin cracks and crevices like joints and penetrations, window and door frame installations, and thermal and acoustic insulation.

When to Use

Apply the Solutions Polyurethane Foam Gun when you wish to quickly and accurately fill joints with foam for complete uniform measures against pest, animals, and more.

Pests may invade indoors at any time during the year when conditions outdoors are less conducive to their survival. Your peak pest activity may depend on the local climate and your geographical location.

Safety Information

Solutions Polyurethane Foam Gun is safe to use around children and pets when used according to the product manual instructions. Always wear the proper personal protective equipment (PPE) when handling this professional foam applicator gun and foam products.

The gun must never be aimed at oneself or other people. The foam manufacturers' safety regulations regarding application must be observed.

Special Considerations

The Solutions Polyurethane Foam Gun seals tightly, so that once the bottle has been screwed into place, the product contained does not dry up. Clean the gun carefully if you do not expect to use it for some time.

When the viscosity changes, it may be that foam is released from the needle packing adjusting screw. In this case, clean the parts at once of any foam and turn the screw clockwise with a N. 8 spanner. This seals the (P.T.F.E) packing in the gun and prevents issue of foam. At the same time also check that closing needle moves freely, if necessary by lubricating it where it joins the screw and packing.

*We do not accept returns on equipment or electronics, all sales are final. We do this to ensure that the products we send out are brand new, never opened, and fully operational for our customers to ensure the packages are covered by their respected manufacturer's warranties.