• Call (800) 479-6583
  • Mon-Fri 8am-5pm
  • |
  • Sat 9am-5pm


Free Shipping on All Orders

Replacement part to repair MistAway Gen 3 (Gen III+) - Mini Bellows Pump.

Includes inlet and discharge tubing.


Part number 21035

Target Pests


For Use In

Mistaway Mosquito Misting Systems


How to Replace the MistAway Bellow Pump

Time: 15 minutes
Phillips head screwdriver (magnetized)
zip tie snip and zip tie
paper towels for blotting concentrate
Gen 3 Mini Bellows Pump, including tubing (#21035)

1. Remove bottle. Reposition controller and shroud. See Gen 3: Access Components by Repositioning Shroud.

2. Remove existing bellows pump

C. Disconnect bellows pump lead (brown, white wires, 2 pin connector) from wiring harness.

D. Pull clear flexible tubing on the right (discharge) side of the bellows out of the batch tank.

E. Snip zip tie securing dark flexible tubing to hose barb on coupler and pull tubing off the hose barb. Use paper towels to blot any concentrate that may leak.

F. The bellows pump frame is secured to bracket with two screws as shown. Using magnetized Phillips head screwdriver, first remove screw nearest you. Pull the pump slightly toward you, and then loosen the back screw (without removing it.).

G. Slide bellows pump toward you and remove from unit.


3. Replace with new bellows pump

A. Position new bellows pump on the bracket and slide it back so that the notch on the pump touches the back screw and then tighten the screw. Secure the front of the pump frame to the bracket with the other screw.

B. Slide the free end of the dark flexible tubing to the hose barb on the coupler and secure with zip tie.

C. Push the clear flexible tubing on the right (discharge) side of the bellows pump into the grommet above the batch tank so that concentrate will pump into the batch tank. DO NOT FORGET TO DO THIS!

D. Connect the bellows pump lead (brown, white wires, 2 pin connector) to the wiring harness.

4. Return shroud and controller to original position. See Gen 3: Access Components by Repositioning Shroud

5. Test bellows pump.

A. Insert the insecticide bottle into the coupler and run a charge.
MAINTENANCE Menu, scroll to CHG.
Press and hold Green ► button for 3 seconds.
DOSE will flash for an extended period.

B. While DOSE is flashing, lift the controller from its well in the shroud. You should be able to see the white plastic bellows contracting and expanding. After the pump primes, you should see be able to see the insecticide moving through the clear discharge tubing.

How To

The bellows pump is the black and blue component mounted to a bracket on the left back wall of the unit.


Product Q & A

Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
How easy is it to replace the pump and how do I know if this is really the issue?
Richard on May 24, 2017
BEST ANSWER: You would do a visual inspection to see if this is the main issue. First, remove the controller to the black plastic shroud. It will have 4 screws on each corner that can be taken off. Once the controller is taken out you will be able to see the tubing connected to the pump. Navigate to the maintenance menu and run a manual charge (CHG). If the pump is working you will start to see the insecticide flow through the clear tubing (it could take a few minutes). If there is no flow replace the pump or the valves in the pump head. You can always call us to walk through this process.

Customer Reviews

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Fast Free Shipping on the Bellow Pump, I was able to get my mistaway back up and running on a couple of days.
May 24, 2017

Contact Us